How to Convert Units (Length, Weight, Temperature and Area)
Updated: 2026-11-02
A unit conversion is a multiplication by a fixed factor — except temperature, which needs a shift as well as a scale, because its zero points differ. The converter on this page covers the four everyday categories: length, weight, temperature and area, with exact SI-based factors so a result is as precise as the conversion allows. This guide explains the mechanics, the special cases (temperature and the Indonesian tumbak), and shows the exact factors the tool uses, and why a conversion you run today will still match one you run a year from now.
The short answer
To convert a value, multiply it by the factor that turns the source unit into the target unit: 1 mile = 1.609344 km, 1 kg = 2.204623 lb, 1 m² = 10,000 cm². Temperature is the exception — it needs an offset plus a scale, because Fahrenheit and Celsius zero points are not the same.
The converter picks the right factor for you from a fixed table of exact SI-based values, so a conversion is as precise as the math allows. It covers four categories, lets you swap the direction with one tap, and works completely offline.
- Length, weight, temperature, area
- Linear: value × factor (1 mile = 1.609344 km)
- Temperature: scale + offset (°F = °C × 9/5 + 32)
- Works offline — the factor table is built in
The four categories and how they differ
Length and weight are linear: one unit of the source equals a fixed number of the target, so the whole conversion is a single multiply. Area is the square of length, so its factors are squared (1 m² = 10,000 cm², not 100). Temperature is the only non-linear category, because the scales start at different points and step at different sizes. Knowing which kind you are doing is the first step to getting it right.
Length and area
Length units are related by fixed factors: 1 m = 100 cm, 1 km = 1000 m, 1 mile = 1.609344 km. Area is length squared, so the factors are the squares of the length factors: 1 km² = 1,000,000 m², 1 m² = 10,000 cm². The tool includes the Indonesian tumbak, 3 m in length and 14 m² in area, in both lists.
Weight and temperature
Weight uses the same linear multiply, with the pound defined exactly as 0.45359237 kg, so 1 kg = 2.204623 lb. Temperature is different: because °C and °F zero points differ, converting needs both a scale and an offset. °C to °F is value × 9/5 + 32, and °F to °C is (value − 32) × 5/9. Absolute scales like Kelvin and Rankine just add a constant shift on top.
A worked example: miles to kilometres
Convert 5 miles to kilometres. Multiply by the exact factor: 5 × 1.609344 = 8.04672 km. Because the factor is exact, the answer is as precise as the input — no rounding beyond your display.
Now convert the same 5 miles to metres: 5 × 1609.344 = 8046.72 m. Both results come from the same exact definition; the converter just applies the matching factor from its table and shows the formula used alongside the number.
Temperature: the offset that trips people up
Temperature conversions are the most common source of mistakes because it is not a plain multiply. The formula for °C to °F is (°C × 9/5) + 32, and for °F to °C it is (°F − 32) × 5/9. The '32' is the offset that accounts for the two scales having different zero points — water freezes at 0 °C but 32 °F.
Absolute scales shift by a constant: Kelvin is Celsius + 273.15, and Rankine is Fahrenheit + 459.67. The converter applies the correct scale-and-offset combination for every pair, so you never have to remember which direction subtracts and which adds.
Tumbak: the unit not in most calculators
The tumbak is an Indonesian unit, so most world calculators omit it. This converter includes it in both length and area, where it is 3 metres long and 14 square metres in area.
Because the factors are exact and defined in the table, tumbak converts the same way as any other unit: pick tumbak as the source, choose your target, and the value is multiplied by the matching factor — 1 tumbak = 3 m, and 1 tumbak (area) = 14 m².
A second worked example: kilograms to pounds
Convert 82 kg to pounds. Multiply by the exact factor: 82 × 2.204623 = 180.779 lb. If you then round to the whole number you will usually quote, that is 181 lb. Because the factor is exact, every digit before you choose to round is real, not an estimate.
Now reverse it: 180 lb × 0.45359237 = 81.6466 kg. You get back a number very close to your starting 82 but not identical, because rounding 180.779 down to 180 lost a little. That small gap is the round-trip cost of rounding, not a flaw in the math. Keep the full precision through intermediate steps and only round at the very end to avoid it.
A quick-reference of common conversions
Most everyday jobs need only a handful of factors, so here are the ones you will reach for most often. Length: 1 inch is exactly 2.54 cm, 1 foot is 30.48 cm, and 1 mile is 1.609344 km. Weight: 1 pound is exactly 0.45359237 kg, and 1 kilogram is 2.204623 lb. Area: 1 acre is 4046.85642 m², and 1 hectare is 10,000 m².
Keep these in mind when you check the calculator: a factor you remember independently is the fastest way to sanity-check a result before you act on it. If the number it gives you disagrees with the factor you know, stop and re-enter your units rather than trusting the output.
- 1 inch = 2.54 cm (exact)
- 1 mile = 1.609344 km
- 1 kg = 2.204623 lb
- 1 hectare = 10,000 m²
Why exact factors matter
Many conversions are exact by definition — the metre per inch, the kilogram per pound, the mile per kilometre are all defined, not measured. That means a result is exact as far as the input is, and any rounding you see is the display's, not the math's.
The converter works entirely offline from a built-in table of these exact factors. There is no network round-trip to lose precision and no account, so a conversion you need for a recipe, a build or a trip is instant and repeatable. Because nothing is measured and nothing is fetched, the same input always gives the same output, which is what you want when the number feeds a decision.
- Factors are exact SI-based definitions, not rounded estimates.
- Area factors are the squares of length factors — watch the units.
- Temperature needs a scale and an offset, not just a multiply.
- Everything runs offline; no data ever leaves your browser.
Frequently asked questions
How do I convert between units?
Multiply the value by the factor that turns the source unit into the target unit. For example, 1 mile = 1.609344 km, so 5 miles is 5 × 1.609344 = 8.04672 km. Temperature is the exception: it needs a scale plus an offset because the scales start at different points.
What is tumbak, and how do I convert it?
The tumbak is an Indonesian unit. In this converter it appears in length as 3 metres and in area as 14 square metres. Convert it like any other unit: choose tumbak as the source, pick your target, and the value is multiplied by the matching exact factor.
How do I convert temperature without a formula app?
Use the offset-and-scale rules: °C to °F is (°C × 9/5) + 32, and °F to °C is (°F − 32) × 5/9. The 32 is the offset because water freezes at 0 °C but 32 °F. Absolute scales like Kelvin (Celsius + 273.15) and Rankine (Fahrenheit + 459.67) are just a constant shift on top.
What categories does the converter cover?
Four: length, weight, temperature and area. Length and weight are simple multiplies, area is the square of length (so its factors are squared), and temperature is the only non-linear category that also needs an offset.
Why are my area conversions so different from length ones?
Because area is length squared. If 1 m = 100 cm, then 1 m² = 100 × 100 = 10,000 cm², not 100. The converter uses the squared factors for area, so 1 km² = 1,000,000 m².
Is the result as precise as possible?
Yes. The factors are exact SI-based definitions (for example, 1 pound is exactly 0.45359237 kg), so a conversion is as precise as your input. Any rounding you see is the display, not the math. The tool shows the formula used alongside the number so you can check it.
Does it work offline?
Yes. The whole factor table is built into the page, so conversions run entirely in your browser with no network. You can use it on a flight or in a basement with no signal, and the numbers you enter are never transmitted or stored.
What is the difference between a linear and a non-linear conversion?
A linear conversion is a single multiply by a fixed factor — length, weight and area. A non-linear one needs more than a multiply: temperature also needs an offset because its scales start at different zero points. The converter handles both automatically for every pair of units.